Todas las entradas de: Steven Henson

Things to Know For a Successful Nighthawk Router Setup at Home

Netgear Nighthawk WiFi router is one of the most-used networking devices to get WiFi everywhere in the home or workplace. However, to make the most of the Netgear router, one needs to set it up in a proper way. Below are the basic steps to perform a successful Nighthawk router setup.

Before You Get Started With the Setup

Let’s have a quick glance at the things you need to take care of:

1. Check Your Internet Connection

In case you don’t have a good internet connection, the router setup experience will be maddening. The easiest way is to connect your device to the modem or gateway provided by your Internet Service Provider or ISP. Once your device detects an internet connection, you are all set to install your WiFi router.

2. Gather Information

It is an obvious step but an important one that will save you from frustration when you are in the middle of Netgear WiFi router setup. Make notes including the important setup information such as the default Nighthawk router login details.

3. Check for an App

Netgear offers you both a web dashboard and the Nighthawk app that you can use for both setup and management. With the Netgear Nighthawk app, you don’t need to use a computer to configure the router.

4. Install and Connect Antennas

In the event that your Netgear router comes with antennas, you need to install them before getting started with the Netgear wireless router setup process.

Netgear WiFi Router Setup Steps

Step-1: Decide Where to Place Your Router

The best place for your Netgear WiFi router is an open area because you will benefit from even coverage. But at times, it is not easy to find a location in the open as you have to connect your router to the modem. So, keep the Netgear router in an open area as well as closer to the existing modem.

Step-2: Connect the Modem to Your Router

For this step, you will need an Ethernet cable. Insert one end of the Ethernet cable into the modem whereas another end into the Netgear wireless router. After that, put the modem on power and let it boot up. Also, plug your Netgear router into an electrical outlet and turn it on.

Step-3: Use Web Dashboard or App

In order to continue with the Netgear router setup, there is a need to access the web dashboard or download the Nighthawk mobile app. To access the web-based dashboard, connect your computer to a WiFi network and visit www.routerlogin.net via a web browser. If you are unable to access the default web page, reboot your Nighthawk device as the router troubleshooting measure.

Step-4: Enter the Router Login Details

Whether you are using the Nighthawk app or the web dashboard for setup, the next step requires you to enter the default username and passphrase. Once done, click on the Log In button.

Step-5: Set up Your Router

After logging in, you will land on the Netgear genie smart setup wizard. This wizard will provide you on-screen instructions to install your Netgear wireless router. The same goes for the Nighthawk app. The app will walk you through the setup steps as soon as you logged into your router.

That’s how you can set up and install your Netgear WiFi router. Still having queries? Feel free to drop them down in the comments section.

Quick Tips to Access Mywifiext.net

When you try to access the default web address www.mywifiext.net to set up your Netgear extender, you might receive one of the following error messages:

  • Unable to connect.
  • You are not connected to the extender’s WiFi network.
  • Page cannot be displayed.
  • Server not found or can’t find the server.

The above-mentioned error messages occur because mywifiext.net is not a regular internet website that you can access any time. It is a local web address that used for opening the settings of your Netgear WiFi range extender. Besides, if you see something else other than one of the error messages above, make sure that you entered the web address correctly in your browser’s address bar. A mistyped or typos in the web address might take you to a third-party website that attempts to steal your login credentials or your personal information.

So, to prevent typos while typing the web address, walk through the steps given below in exact order and gain access to mywifiext.net without any ado. Let’s start over!

Troubleshooting issues while connecting to www.mywifiext.net:

Placement

Bring your Netgear range extender into the same room as your WiFi router.
After the Netgear extender setup is completed successfully and you have an active internet connection, you can move the device anywhere in your house.

Power Supply

Make sure that your Netgear range extender is plugged into a working and fluctuation-free power source.

LEDs

The power LED on your Netgear extender must be stable. Apart from this, if your Netgear device has a PC to Extender LED or a Device to Extender LED, ensure that that it is not blinking. On the off chance that the LEDs on your Netgear device is not lit, then unplug your devices from the power socket for some time and after that plug them back again in.

Open a Device

  • Power on a computer, laptop or mobile device.
  • Open a web browser in any of your smart device.
  • Head towards the browser’s address bar.
  • Enter mywifiext. To prevent any login issues, do not use the browser’s search bar for accessing the web address.

If you still can’t access the web address, try a few troubleshooting tips given-below.

  • Make sure that your Netgear extender is receiving continuous and uninterrupted router’s WiFi signals.
  • The web browser you are using must be up-to-date.
  • If you are already using an up-to-date web browser, then clear cache, cookies, browsing history or any kind of malware from it, close all the tabs, restart your device, and try accessing the web address again from another web browser.
  • Assign your device (computer, laptop or smartphone) a static IP address.


If you still can’t access the web address, try resetting your Netgear extender back to the default settings.

To reset your Netgear extender without any hassle, follow the steps given below.

  • Disconnect your Netgear extender from your main router and other devices.
  • During the reset process, plug in your Netgear extender away from the reach of your router’s WiFi network.
  • Once done, find the Netgear extender’s reset hole and push it using any thin and pointed object.
  • Hold the reset hole and release it when the power LED on your Netgear extender starts blinking.
  • Thus, your Netgear extender resets successfully.

Make a Connection Again

  • Unplug your Netgear extender and place it near to your router again.
  • Connect your Netgear WiFi extender to the router using a wired or a WiFi connection.
  • Open a computer or laptop and try accessing the web address again. In the event that mywifiext.net is still not working for you, try to login via 192.168.1.250.

Still, facing the same issue?

If you still can’t access mywifiext.net or 192.168.1.250, then without any delay, reach out to us via comments right away.

How to Connect Netgear Extender to My Home Network?

Netgear WiFi range extenders are very helpful in extending the range of existing WiFi network and spreading it to hard-to-reach areas. But 4 out of 5 users face issues while connecting Netgear WiFi extender to their home network. If you are also facing issues while connecting Netgear extender to your home network, this post can help you out.

Prior to going through the tips given-below for connecting Netgear extender to your home WiFi network, make sure of the following:

  • Netgear WiFi extender must be previously connected to the router’s WiFi network.
  • Apart from this, Netgear extender must obtain a valid IP address.

Now, let’s get started with the process “how to connect Netgear extender to the home WiFi network”.

There are two ways through which you can connect Netgear WiFi extender to your home network.

  • Connect via Ethernet.
  • Connect via WiFi.

We will discuss both the ways of connecting Netgear extender to your home WiFi network one by one.

To connect Netgear WiFi range extender to your home network via Ethernet:

  • Connect the Netgear extender into a working wall outlet near to your WiFi router.
  • Launch a web browser on a computer or laptop.
  • Type mywifiext.net into the web browser’s address bar.
  • Press the Enter key.
    The login page will display.
    Enter the default username and password that you chose during Netgear extender setup process. If you have customized the extender’s username and password, use them.
    Click on Log In or Done.
  • Select Setup and click on Wireless Settings option.
  • Locate the Security Options. Under them, verify that the value in the Password or the Network Key field matches your existing router password.
    Once done, click on Apply to save the changes. On the off chance that the password does not match with your router password, change it right away.

Connect your router and WiFi devices to the Netgear extender and enjoy the internet speed in every corner of your house without any interruption.

Bonus Tip: Placing the Netgear extender and the WiFi router openly on a clean and higher shelf will definitely give you unexpected internet speed even in blind spots. Besides, place your devices away from public WiFi, Bluetooth speakers or devices, cordless phones, baby monitors, etc.

To connect Netgear range extender to your home network via WiFi:

  • Firstly, locate the factory reset hole on your Netgear WiFi range extender.
  • Push the reset hole on your Netgear device with the help of thin, clean, and pointed object.
  • Keep holding the reset hole for a couple of seconds and then release it.
    Your Netgear range extender resets successfully.
  • Now, connect your Netgear extender to the router’s WiFi network.
  • Open a computer, laptop or a mobile device and launch a web browser in it.
  • Type www.mywifiext.net into the web browser’s address bar.
  • Press Enter.
    Netgear extender login page displays.
    Enter the extender’s default username and password. If you have personalized the extender’s login details, use them instead of the default ones.
  • Click on Log In.
  • Follow the on-screen prompts to connect your Netgear extender to your home WiFi network.

Note: If the web address mywifiext not working for you, use the default Netgear extender IP address.

Bonus Tip: Updating Netgear extender’s firmware (whenever available) will help you in getting the most out of your device and take you internet experience to the next level.

In this way, you can easily connect your Netgear extender to your home network. We hope that the 2 easy ways given in this post have helped you out? In the event that you got stuck at any step and need immediate technical assistance, reach out to us via comments. We are 24×7 available to help you.

How to Reboot Netgear EX3700 Extender Remotely

Netgear EX3700 AC750 WiFi extender gives an extreme boost to your existing wireless network and coverage. Delivering AC WiFi up to 750 Mbps, the extender is ideal for online gaming and HD video streaming. Although the extender comes with various useful features, it is susceptible to technical glitches. Whether the EX3700 dropping the internet connection or it is not working, sometimes all it takes to troubleshoot the issue is a power cycle or reboot.

This is not only a common and simple step to resolve an issue completely but it also serves as an important step during more in-depth troubleshooting procedures. Here, you will learn how to reboot the Netgear EX3700 extender remotely. Let’s take the plunge.

What is Rebooting and How does it Help?

Rebooting is also known as power cycling and restarting. It is an act of shutting down a device and then powering it back up again.

Electrical devices like Netgear EX3700 WiFi extender work on hardware and software and may be overloaded with information or even overheat, resulting in degrading the performance. By turning off the device, it refreshes the built-in RAM and makes it work like a new device.

When Should I Restart My Netgear EX3700 Extender?

  • WiFi connection is sluggish
  • Hardware or driver error
  • Facing Netgear EX3700 setup issues
  • Can’t update the firmware on the extender
  • Power LED is amber
  • Getting a blinking orange light on the extender
  • Unable to connect to the network
  • Can’t log in to Netgear EX3700 extender
  • The extender’s network is not showing on the available networks’ list

Benefits of Power Cycling the Netgear Extender

  • Flushes RAM
  • Speeds up your extender
  • Improves the extender’s performance
  • Fixes slow internet

Reboot Netgear EX3700 Extender Remotely

Without pressing the physical On/Off button on your extender, you can power cycle it remotely. All you need to do is simply connect to Netgear_ext SSID and log in to your EX3700 extender’s user interface. Let’s walk you through the complete steps to restart your Netgear EX3700 range extender using the web GUI:

  • Power up your Netgear wireless range extender. Ensure that it is acquiring steady power supply from the wall outlet.
  • Grab a damage-free Ethernet cable. Insert its one end into the extender’s Ethernet port while another end to the existing router.
  • Remember to check if the home router is turned on. If not, power it up immediately.
  • Now, use your computer and launch the web browser you often access.
  • Take the mouse cursor to the top-left corner of the browser window and click on it.
  • Now, move your fingers on the keyboard and type www.mywifiext.net.
  • The mywifiext login window comes into view.
  • Again, use the keyboard and type admin credentials to log into your extender.
  • After clicking on the Log In button, wait for the Netgear genie page to load properly.
  • Go to the Settings menu.
  • Click on the Restart button.
  • A confirmation pop-up appears. Simply hit the Yes button.
  • Let the restart process finish completely.

Done! Your Netgear EX3700 WiFi range extender has been rebooted remotely. Stay tuned with us for more helpful posts.

How to Secure Linksys RE6500 WiFi Range Extender

Linksys RE6500 WiFi extender is a device that every user blindly relies for internet surfing, video streaming, online gaming, completing daily tasks, and much more. But most of the users ignore to keep their Linksys device secure from potential threats.

If you want freeloaders to have access on your personal information, then you can neglect securing your WiFi. And if you want your WiFi to be secured, go through the list of security measures given in this post once.

Proven Ways to Secure your Linksys RE6500 WiFi

Fasten Your WiFi with Password

Protect your Linksys RE6500 WiFi by changing its default login credentials. You can easily change the admin password of your RE6500 by navigating to its settings via http//extender.linksys.com.

Choose a Strong Password

The default admin password is very easy to crack by hackers. If an anonymous person knows the make and model of your device, they can easily get into it and steal all your information and leech your WiFi also. To prevent this, choosing a hard-to-crack password of at least 16 characters would be a best way to keep bad elements away from your Linksys extender’s WiFi network.

Tip: Use upper case, lower case, symbols, letters, and alphabets in your password. This will make your password unique and strong.

Enable Network Security

Linksys RE6500 extender supports a number of advance securities such as WEP, WPA, and WPA2. All of them are very helpful in securing your Linksys RE6500’s WiFi network. But we suggest securing their Linksys device with WPA2 security.

Turn off Remote Access

You can access the settings of your Linksys WiFi range extender from anywhere using the remote access feature. Though it is the easiest way of accessing your extender remotely but it can also be accessed by any one that is connected to your RE6500’s WiFi network. So, what you are going to do to stop any one from accessing your extender’s WiFi? Simply, turn off the remote access feature when not in use.

Keep Linksys RE6500 Extender’s Firmware Up-to-date

After Linksys WiFi extender setup, it is important to update its firmware for securing it from potential threats. Check for the latest firmware update for your device by accessing extender.linksys.com web portal. And if the new firmware for your RE6500 is available, simply update it by going through the on-screen instructions and protect your device from bad people.

Tip: Turn on the auto-update feature so that you will get notification whenever your device needs an update.

Cut off WiFi Lechers

For this, you simply have to stop sharing your WiFi password with everyone. You don’t know which one of them is spreading your WiFi to their friends. So, create a separate WiFi for your guests and apart from this, change the WiFi password frequently.

Don’t Use Public WiFi

This is the very important point to consider. Do not use public WiFi for performing online tasks, online payments, Linksys extender setup RE6500, or doing anything online. Using public WiFi will not only steal your personal stuff but also ruin your internet experience. So, stop searching for free WiFi. Create your own WiFi network in every nook and cranny of your house after correctly performed Linksys extender setup.

The Final Words

Securing your Linksys RE6500 WiFi range extender must be a foremost thing for those who want their WiFi and personal information safe. However, a non-techy must seek help from a technician to gain success in securing their Linksys extender’s WiFi network from on-going threats. Hopefully, this post has proven helpful to you in securing your Linksys extender and to get the most out of your WiFi.

Proven Tactics to Fix Netgear Router Error 651 Instantly

Netgear WiFi router is one of the widely-used networking devices to get an uninterrupted internet connection. But like any other networking device, it is also prone to technical glitches. After setting up the Netgear router, you may see an error pop-up saying ‘Error 651 Connection Failed’. In case you are completely unable to understand this error, don’t need to worry at all as we are here to help you out. Scroll down to read more.

Netgear router error code 651 signifies that the internet connection you are trying to establish is failing. There may be several reasons why the network connection fails. It is extremely important to rectify the Netgear error code 651 prior to anything wrong happens with your Netgear WiFi router. Due to this error, you may also fail to access the Netgear router login web page.

Reasons Behind Netgear Router Error 651

The error generally appears because of the following reasons:

  • Incorrect configuration of the internet protocol
  • The network card driver is corrupted
  • No internet connectivity
  • The router is improperly configured
  • The drive port file is stored on a wrong location
  • Two or more devices are using the same IP address as that of your router’s IP
  • Corrupted registry files

Solutions To Fix Netgear Router Error Code 651

Note: The below-explained troubleshooting steps will remain the same no matter whether you have employed the Netgear Nighthawk AC1900 setup or are using an old router.

1. Reconnect Your Netgear Router

This is the simplest troubleshooting step to get rid of the Netgear 651 error. To reconnect your Netgear WiFi router:

  • Power off your Netgear router.
  • Wait for some time.
  • Thereafter, power it up again.
  • Connect your Netgear router to the modem via an Ethernet cable.
  • Now, connect to a WiFi network.

2. Recreating Dial-Up Connection

Chances are that the devices connected to your Netgear router get hanged. In such a case, you need to recreate your dial-up connection. Let’s have a look at the required steps to get the job done:

  • Turn on your PC.
  • Go to the Change Adapter Settings section.
  • After that, a copy of your current internet connection will be created.
  • Remove the old connection and redial the new one.

3. Reset TCP/IP on Your Computer

The next troubleshooting tip to fix the Netgear router error 651 is to reset the Windows networking stack. Here are the do-follow instructions:

  • Switch on your computer.
  • Launch the Command Prompt window.
  • Enter the Reset command followed by the TCP/IP.
  • After that, restart your computer.

Once done, try accessing the router login web page. In case the page opens properly, it indicates that the internet connection has been set up. If not, move to the next troubleshooting tip.

4. Fix the Drive Port File Issues

The drive port file is a mediator meant to connect hardware with the software. And if it is installed in a wrong manner or having the wrong name, then you may come across the Netgear router error 651. To fix the issue, rename the drive port file by following the steps given below:

  • Open the My Computer folder.
  • Go to the C: drive.
  • Click on the Drive folder and look for the driver file.
  • Once found, right-click on the file and rename it.
  • Restart your PC.

Done! The Netgear router error 651 should be fixed now.

These were our proven troubleshooting tricks to rectify the Netgear error 651 instantly. Stay tuned with us for more updates.